>> 当前的位置 >> 售后服务
 
   

警告:对工具进行维护保养前,必须将工具的电源切断 

1、 保持工具完整,清洁。通风口畅通,及时给工具添加润滑油。 
2、 经常检查电源线,电源插头,开关是否良好;钻头是否锋利等。如有故障或部件损坏,请专门人员进行修理或更换部件。 
3、工具使用后,要及时保养。外壳脏了以后,可用柔软的布擦拭,不可使用溶剂,如汽油,酒精,四氯化碳,氨水等,否则会损坏部件。 
4、不要使电源线接触热源,油脂。防止电源线擦破,割破轧坏。 
5、工具不用时,应放在干燥,清洁和无腐蚀气体的环境中。如工具损坏,要送指定的修理部修理。错用工具或由非专业人员修理工具所发生的任何损坏,均不属于三包范围。 
注意事项 
1、使用环境条件:(1)海拔不超过1000m;(2)环境空气温度不超过40℃,(3)空气相对湿度不超过90%(25℃); 
2、操作前要可靠接地,工作场所必须保持清洁,穿戴绝缘手套、胶底鞋、防护镜,不可让工具被雨淋; 
3、外部电源电压与额定电压波动不大于5%; 
4、系好安全带,以免突然断电工具失去磁性,造成事故; 
5、长期停用的电钻,使用前必须先检查其绝缘电阻是否大于2MΩ。若达不到,必须进行干燥处理,直至其绝缘电阻大于2MΩ后方可使用; 
6、操作时,吸盘必须置于牢固且足够大的平面和厚度的钢板构件上(钢板厚度不低于12mm),以保证其有足够的稳固性; 
7、在弱磁性材料上作业(铜、铝、非金属等)则必须加装钢板辅助基面; 
8、请按规定使用速率操作机器,勿让其超负荷,可达到最佳工作效率并提高工作安全; 
9、电磁铁长时间工作后,应断开电磁铁电源开关,以降低其温度,然后再继续工作; 
10、维修及更换零部件或附件时,务必断开电源(直接拔出机器的电源插头); 
11、发生机械故障时,必须由专业人员进行检查、维修,否则可能会给操作者带来危险; 
12、细心地保养磁力钻,并及时更换合适的配件,定期检查,并妥善地放于干燥且儿童无法取得之处。工作时,更不要让儿童触摸工具和延伸线; 
13、吸盘不可接触尖锐的金属、砂石等,以免影响吸盘底部的平整度及碰伤吸盘底部的线圈而发生危险; 
14、导板、齿轮的机械摩擦部位应适时添加润滑油,防锈防呆; 
15、不要与腐蚀性气体及酸碱等化学物质接触。

 

Warning: the maintenance of the tool before the tool of power must be cut off
1, to maintain integrity tools clean. Open vents, add the oil in time to the tool.
2, regular checks of the power cord, power plug, switch is good; bit is sharp and so on. Failure or damage to any parts, please specialized personnel in the repair or replacement of parts.
3, tool use, to the timely maintenance. Dirty shell after soft cloth can be used, not the use of solvents, such as gasoline, alcohol, carbon tetrachloride, ammonia and so on, otherwise damage the components.
4, do not touch the power cord so that heat and grease. Power cord to prevent abrasions, cut bad rolling.
5, tool when not in use, should be dry, clean and non-corrosive gas environment. Damage such as tools, it is necessary to send repair修理部designated. Misuse of tools or tool by non-professionals to repair any damage that occurred, three bags of scope are not.
Notes
1, the use of environmental conditions: (1) does not exceed an elevation of 1000m; (2) ambient air temperature does not exceed 40 ℃, (3) air relative humidity of not more than 90% (25 ℃);
2, operation of a reliable ground before, in the workplace must be kept clean, wearing insulated gloves, rubber-soled shoes, protective lens, not to allow the tool to be rain;
3, external power supply voltage and rated voltage fluctuations not more than 5%;
4, seat belts, so as to avoid a sudden loss of magnetic power tools, resulting in the accident;
5, long-term out of an electric drill, using the former to check the insulation resistance is greater than 2MΩ. If not, must be dried until the insulation resistance is greater than before the use of 2MΩ;
6, operation, and the sucker must be firmly placed in the plane is large enough and the thickness of the steel components (steel thickness of not less than 12mm), to ensure there is sufficient stability;
7, operating in a weak magnetic material (copper, aluminum, non-metallic, etc.) must be the installation of auxiliary base plate;
8, please use the rate required to operate the machines, not to overload, can achieve the best efficiency and enhance safety at work;
9, after a long solenoid, electromagnet power switch should be disconnected in order to reduce its temperature, and then continue to work;
10, maintenance and replacement of parts or accessories, be sure to disconnect the power (direct pull plug the machine);
11, mechanical failure, must be professionals in the inspection and maintenance, otherwise the operator might be dangerous;
12, carefully drill magnetic maintenance and timely replacement of the appropriate accessories, regularly inspected and properly disposed of at the dry and can not be made of the children. Working hours, not to allow children to touch the tools and the extension line;
13, sucker acute non-contact metal, gravel, etc., so as not to affect the flatness of the bottom sucker and sucker bumps at the bottom of the coil and the danger;
14, guide plate, gear parts of the mechanical friction should be added in due course lubricants, rust-proof heart touching;
15, not with the corrosive gases and acid-base, such as exposure to chemical substances.

 
扬州市金玉电动工具有限公司位于环境优美、交通便利的扬州北绕城高速公路出口处---酒甸工业区,是集设计、生产、销售于一体的磁座钻系列及其配套产品的制造商.
  后台管理 | 公司简介 | 联系我们 | 技术支持:扬州世纪洲

Copyright©2008-2015 扬州市金玉电动工具有限公司 All rights reserved. 苏ICP备07031278号